Matching of electric door remote control

 对拷遥控器的出现，使电动遥控门遥控器的匹配变得非常简单，轻松两步就能快速完成固定码遥控器的匹配。

There remote control, the remote control, remote control electric door is very simple and easy two steps can be finished quickly, fixed code remote control.

(1)特点不需要拷贝机，不需要知道震荡电阻，直接用遥控器来复制遥控器，立马能用。

(1) the character does not need a copy machine, does not need to know the shock resistance, directly uses the remote control to copy the remote control, and it can be used immediately.

(2)使用此款遥控器的前提

(2) the premise of using this remote control

①原遥控器可以用，而且能够正常遥控。

The original remote control can be used, and can be normally remote control.

②需要知道遥控器的频率c例如390MHz，400MHZ等）

(2) need to know the frequency of the remote control C, such as 390MHz, 400MHZ, etc.

③遥控器的芯片是以下可拷贝的芯片SC2260/SC2262/HS2260/HS2262/PT2262/PT2260/EV15271SCL1527/SC5211/FP527/PT2240/HS2260/SC2240/HS1527／CL2262/HS2240/PT2264/LX2260/X2262/LP8527/HX2262/HX2260（市场上大多数固定码和部分学习码遥控器都可兼容）

The remote controller chip is the following copy of the SC2260/SC2262/HS2260/HS2262/PT2262/PT2260/EV15271SCL1527/SC5211/FP527/PT2240/HS2260/SC2240/HS1527 / CL2262/HS2240/PT2264/LX2260/X2262/LP8527/HX2262/HX2260 (chip on the market most of the fixed code and part learning code remote control are compatible)

(3)具体操作方法

(3) specific operation method

①清码。同时按下遥控器上排的两个按键，"开门"键和"关门"键，指示灯闪一次后约2s后快闪即表示清除成功。清除之后按遥控器4个按键指示灯仅闪一下后熄灭。

A clear code. At the same time, press the two keys of the remote control, "open the door" key and "close the door" key, indicating the light flicker after about 2S after the flash is to indicate the success. After scavenging, the 4 keys of the remote control only flicker and then go out.

②对拷。一个手拿着原装的遥控器，另一个手拿着万能拷贝遥控器，两个遥控器尽量靠近，同时按下两个遥控器"开门"键，拷贝遥控器指示灯快速闪动即表示复制成功，然后再松开您的手。依次按相同方法，将其他三个按键拷贝上去。

The copy. One hand holds the original remote controller. The other hand holds the universal copy remote controller. The two remote controllers approach as close as possible. Meanwhile, press the two remote control "open door" keys, and copy the remote control indicator to flicker quickly, that is to say that the copy is successful, then loosen your hand. Copy the other three keys in the same way.

注意：拷贝时候如果灯不闪动，可以换个位置，比如将两个遥控器的头部对着再拷贝试试。可以多换几个位置试试。

Note: if the light doesn't flicker when copying, you can change the position, for example, try the head of the two remote control in front of the copy. You can try a few more places.

③恢复。若是误操作清除掉有用代码后，在没有重新拷贝其他遥控器之前可同时按下遥控器下排两个按键2s后，指示灯快速闪烁则表示恢复成功。

(3) recovery. If the wrong operation to remove useful code, before re copy other remote control can also press the remote control button two. After 2S, the indicator light flashes quickly said a successful recovery.